Difference between revisions of "Pedal Interceptor"

From Tinkla: Tinkering with Tesla
m
m
Line 54: Line 54:
 
Once in DFU mode, go to the pedal_tesla directory and run  
 
Once in DFU mode, go to the pedal_tesla directory and run  
  
<nowiki>make recover</nowiki>
+
<code>make recover</code>
  
 
=== Guides for Building / Troubleshooting Your Comma Pedal ===
 
=== Guides for Building / Troubleshooting Your Comma Pedal ===

Revision as of 14:15, 8 May 2019

The Comma Pedal is used to provide acceleration and regen braking capability on Tesla cars running Openpilot that do not have iBooster installed.

The Comma Pedal is an accelerator pedal interceptor. It is a device that is inserted between a car's electronic gas pedal and the DU (Drive Unit). It detects the voltage from the accelerator pedal which represents the pedal's position. It then writes that same voltage back out to the DU as if the accelerator pedal had produced it. When Openpilot is engaged, Openpilot sends the virtual acceleration position through the Comma Pedal instead.

The Comma Pedal is connected to the Giraffe on CAN3-EPAS usually using a Y adapter (that you have to make).

What it Does

The Comma Pedal has 4 main systems:

  1. 2 Analog to Digital Convertors
    • This is used to read the voltage from the car's accelerator pedal into the Comma Pedal's processor. The accelerator pedal produces an output Voltage between 0 and 5 Volts.
  2. 2 Digital to Analog Convertors
    • This is used to send voltage back to the car's DU as if the accelerator pedal had produced it.
  3. 1 CAN Bus
    • The CAN Bus is the car's communication network. The Comma Pedal communicates with Openpilot using the CAN Bus. It connects to the Tesla Giraffe on CAN3.
  4. 1 USB
    • This is used to program and monitor the Comma Pedal, itself.

When Openpilot is NOT engaged, the Comma Pedal reads the voltage from the accelerator pedal and just passes it along to the DU.

When Openpilot IS engaged with longitudinal control, the Comma Pedal gets accelerator commands from Openpilot and emulates a accelerator pedal to the DU.

The Comma Pedal is constantly sending the physical accelerator pedal's position to the CAN bus for Openpilot to read.

Obtaining a Comma Pedal (generic infor from Comma.ai wiki)

You cannot buy a pre-built comma pedal from Comma. Perhaps someone will begin selling them, but for now, you must either build it yourself (not recommended) Or have one fabricated through a service like Macrofab.

More information on HOW to do that will be added to this wiki in the future.

You can find an article written by a community member on how to build your own through MacroFab:

Comma Pedal: Building with MacroFab by Joshua F. Rountree

The information needed to build one is located in Comma's EON GitHub repo.

Wiring a Tesla Pedal

Tesla pedal wiring.png
Pedal pinout.png
Pedal connector.png
Pedal CAN connection.png

In order to create your Tesla Pedal you need:

Use the diagram to conenct the female WSP-929 pedal connector to the IN side of the pedal board and the male WSP-929 connector to the OUT side of the pedal connector. Use twised wire (preffered) to conenct to the positions 3 and 6 of the fake-ethernet port of the pedal board to the two JST2 connectors (male and female). We need both because you will plug the female one in the Giraffe's EPAS connector and then the EPAS Harness into the male JSP2. Red should be CAN+ and black should be CAN- (that's the convention also used in the image showing the CAN wire soldered to pins 3 and 6 of the fake ethernet port on the pedal baord).

Flashing the firmware for Tesla Pedal

You have to use a Tesla specific firmware on the pedal in order to work for Tesla. 

The firmware in my repo for the Tesla Pedal is located in /data/openpilot/panda/board/pedal_tesla. You can flash the pedal from your computer or from the EON (I did it from the EON). If you have a new board, it will automatically start in DFU mode. If not, you can enter the DFU mode either using a Panda Paw or by applying 5 volts to a special point on the board while conencting the board to USB (to power it up). That usually requires at least 2 people: one to keep the jumper for 5V in place and the other to connect the USB. Instructions on how to enter DFU mode were create by @jfrux.

Once in DFU mode, go to the pedal_tesla directory and run

make recover

Guides for Building / Troubleshooting Your Comma Pedal

Comma Pedal: Updating the Firmware over CAN by @jfrux Use this guide to update your Comma Pedal for compatibility with Openpilot v0.5.10+

Comma Pedal: Building with MacroFab by @jfrux

Comma Pedal: Flashing the Firmware by @jfrux