|
|
| (3 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | <big><big>Work in Progress</big></big><br />
| |
| − | This page is the first pass at replacing the Main Page "Getting Started" section.
| |
| | | | |
| − | __toc__
| |
| − |
| |
| − | <big><big>Quick Start</big></big><br />
| |
| − | If you are looking to get your EON up and running see the following guides
| |
| − |
| |
| − | == Installing the Giraffe ==
| |
| − | [[File:CH_bus-2.jpg|150px|thumb|right|Has 1&9]]There are currently three options concerning Giraffes for your Model S. You can even make your own [[Tesla Giraffe]].
| |
| − | # Giraffe revC from @AsianTea#7596 on the [https://discordapp.com/invite/Wyna3qy Comma.ai Discord]
| |
| − | #* This solution doesn't need any modification to perform a Radar retrofit.
| |
| − | #* This will work as long as your OBD port pins 1 and 9 like the first picture on the right.
| |
| − | # An EPAS harness from [https://www.ebay.com/str/level2tesla Flyboy222pa on eBay]
| |
| − | #* This path doesn't require a Giraffe.
| |
| − | #* But this will require a 120 Ohm resistor if you want to install a Radar retrofit.[[File:no_CH_bus-2.jpg|150px|thumb|right|Missing 1&9]]
| |
| − | # Giraffe For cars built before May 31, 2013, will need a "TDC Connector".
| |
| − | #* You'll want this variant if your OBD port is missing pins 1 and 9 like the second picture to the right.
| |
| − |
| |
| − | Whichever one of these you end up using, install it into the corresponding port under the dash, in the driver's foot well.
| |
| − |
| |
| − | == Installing the EPAS Cable ==
| |
| − | [[EPAS Harness]]
| |
| − |
| |
| − | == Installing the EON ==
| |
| − | Steps to [[EON#Installing_the_EON|install the EON]] and also how to install OpenPilot.
| |
| − |
| |
| − | == Installing OpenPilot for Tesla on the EON ==
| |
| − | [[EON#Installing_OpenPilot_for_Tesla|Steps to perform OP install]]
| |
| − | === First OpenPilot Drive ===
| |
| − | # Make sure the EON is mounted properly and connected to the Panda by following [[#Installing the EON]]
| |
| − | # Make sure the EON has Internet access (either your wifi at home or a SIM card). Connect to a mobile hotspot if you don't have a SIM card
| |
| − | ## Reboot your EON before turning your car on for good measure
| |
| − | # Turn your car on and verify that the Panda LEDs are pulsing red/blue/purple. If they are green, your panda is not flashed, see flashing instructions here [[Panda#Flashing_the_Panda|Panda Flashing]].
| |
| − | # OpenPilot should switch to "drive mode" and show the camera view with white lane marking
| |
| − | # Make sure that your EON is connected to the Internet or Calibration will not start
| |
| − | # Read up and understand the controls from [[Longitudinal_Control:_ACC#Using_Adaptive_Cruise_Control|Using adaptive cruise control]]
| |
| − |
| |
| − |
| |
| − | IF YOUR CAR IS RECOGNIZED:
| |
| − | # Calibration will increment at above 15mph. It will take less than 30 seconds to fully calibrate. If you move the mount, it's recommended to reset camera calibration under "device settings".
| |
| − | # When driving, Double Pull the Cruise Control Stalk to use OpenPilot
| |
| − |
| |
| − | IF YOUR CAR IS NOT RECOGNIZED
| |
| − | # Ask for help on the #tesla channel of the [https://discordapp.com/invite/Wyna3qy Comma.ai Discord]
| |
| − |
| |
| − | == FAQ ==
| |
| − |
| |
| − | == Glossary/Acronyms ==
| |
