Difference between revisions of "Tinkla Relay"

From Tinkla: Tinkering with Tesla
m
m (Installing the Tinkla Relay)
Line 16: Line 16:
  
 
Tinkla Relay can be either installed using the provided harness directly into the OBD2 port or hardwired directly into the car power and CAN lines. To connect directly to Tinkla Relay you need a Molex 34791-0080 connector with the following wiring:
 
Tinkla Relay can be either installed using the provided harness directly into the OBD2 port or hardwired directly into the car power and CAN lines. To connect directly to Tinkla Relay you need a Molex 34791-0080 connector with the following wiring:
* Pin 1: CAN 1 Low -> connect to Chassis CAN Low
+
 
* Pin 2: CAN 1 High -> connect to Chassis CAN High
+
{| class="wikitable"
* Pin 3: NOT USED
+
!colspan="3"|Tinkla Relay Wiring
* Pin 4: CAN 2 Low   -> not connected on Model S/X
+
|-
* Pin 5: CAN 2 High -> not connected on Model S/X
+
|Pin
* Pin 6: NOT USED
+
|Use
* Pin 7: Ground  -> connect to car ground
+
|Connect to
* Pin 8: 12V -> connect to car power (permanent or accessory, depends on your needs)
+
|-
 +
|1
 +
|CAN 1 Low  
 +
|Chassis CAN Low
 +
|-
 +
|2
 +
|CAN 1 High  
 +
|Chassis CAN High
 +
|-
 +
|3
 +
|Not Used
 +
|
 +
|-
 +
|4
 +
|CAN 2 Low  
 +
|not used on Model S/X
 +
|-
 +
|5
 +
|CAN 1 High  
 +
|not used on Model S/X
 +
|-
 +
|6
 +
|Not Used
 +
|
 +
|-
 +
|7
 +
|GND
 +
|car ground
 +
|-
 +
|8
 +
|12V
 +
|car accessory power or permanent power, depending on application
 +
|}
  
 
== DIP Switches ==
 
== DIP Switches ==
  
 
== How to order Tinkla Relay ==
 
== How to order Tinkla Relay ==

Revision as of 21:49, 14 February 2022

Do you like Tinkering with your Tesla? Do you like adding additional features to it without having to install old style switches to control them? Do you want to control additional lights or devices based on specific conditions of the car (charging, driving, turning left/right, ger forward/reverse, high beams on, blind spot monitoring signals, or specific button presses on the steering wheel)? Then Tinkla Relay is a must have Swiss Army Knife for Tesla Model S/X integrations (and very SOON Model 3/Y).

Tinkla Relay is a device that connects to your Tesla power and CAN and has 4 output relays that are turned on/off based on your settings configured via DIP switches. The maximum output for the relays is 12V and up to 3A total between all on channels at a time. This is enough to drive GPIO signals, trigger relays for larger consumers or turn on notification LEDs.

Talk: Feedback? Ideas? Comments?

What is in the box

  1. The Tinkla Relay board
  2. Dev harness that will allow you to connect to the OBD2 port
  3. 3A mini fuse
  4. Automotive grade hook and loop tape

Installing the Tinkla Relay

Tinkla Relay can be either installed using the provided harness directly into the OBD2 port or hardwired directly into the car power and CAN lines. To connect directly to Tinkla Relay you need a Molex 34791-0080 connector with the following wiring:

Tinkla Relay Wiring
Pin Use Connect to
1 CAN 1 Low Chassis CAN Low
2 CAN 1 High Chassis CAN High
3 Not Used
4 CAN 2 Low not used on Model S/X
5 CAN 1 High not used on Model S/X
6 Not Used
7 GND car ground
8 12V car accessory power or permanent power, depending on application

DIP Switches

How to order Tinkla Relay