Difference between revisions of "Removing the Instrument Cluster"

From Tinkla: Tinkering with Tesla
m (Step-by-Step guide to remove the Instrument Cluster)
m
 
Line 1: Line 1:
 +
{|class="wikitable"
 +
|-
 +
| [[Tinkla Buddy|What is Tinkla Buddy?]] || [[Tinkla Buddy Install Kit|Tinkla Buddy Install Kit]] || [[Tinkla Buddy Installation|Installing your Tinkla Buddy]] || [[Tinkla Buddy Configuration|Configuring your Tinkla Buddy]]
 +
|}
 +
 
====Step-by-Step guide to remove the Instrument Cluster====
 
====Step-by-Step guide to remove the Instrument Cluster====
  

Latest revision as of 13:43, 6 September 2020

What is Tinkla Buddy? Tinkla Buddy Install Kit Installing your Tinkla Buddy Configuring your Tinkla Buddy

Step-by-Step guide to remove the Instrument Cluster

There are multiple videos on how to remove the Instrument Cluster [IC], here is one for the Model S:

Tools worth investing in:


Step 1

Remove the “faux leather” knee-board trim just below the IC and steering wheel. It’s the large piece with a soft touch feel to it. This piece is held in place by pegs. It’s easiest to start over on the right side just below the hazard lights button, to the left of the MCU. Put your palms facing away from you, touching the soft surface, and grab the top ledge of the trim with your fingers and pull back. It will eventually pop out, and you can work your way to the left and remove the parts under the vent to the left of the steering wheel. To be safe, put the piece of trim in a safe place where it won’t get scratched. Back seat, or trunk, are good options.

Winter14.png Winter12.jpg Winter13.jpg

At the same time, go ahead and remove the small “hatch” cover trim panel on the left side of the dash where the door meets the dash. There is a screw in here (red arrow) that holds the top dash trim to the frame which is essential to remove! The video instructions to remove the IC did not include this screw.

The upper right and right pics show other screws that will need to be removed. Go ahead and remove the two on the left now.

Step 2

Winter15.png

Next you have the small piece of trim just above the steering wheel. Note that this can be very tight. It’s held on only with pegs. The IC disassembly video didn’t show this part (it was already loose). You can see two plastic tabs on the left and right side. Don’t grab and pull straight back. Instead, grip them from the bottom and pull the bottom up at a slight angle. The tabs will pop out quickly (see pics below).

Winter16.png Winter17.png

Remove more screws! There are two screws under the small trim piece you just removed, on the right and left sides. Remove both of them. Also, in the right pic below, remove the screw on the right.

Winter18.jpg Winter19.jpg Winter20.jpg

Step 3

It’s dash time! There is a thin plastic panel above the IC, on the bottom of the sun guard. Pry it off with a trim removal tool. It’s held in place with 4 pegs.

Winter21.jpg Winter22.jpg Winter23.png

Next take out two more screws holding the frame to the trim. Then, put in your air-shim tool and pump it up! This is the part where you want to make sure you removed that one screw in the side hatch! Pump it up until you reveal the screws shown in the pics above. At this point, you should be able to remove the silver colored IC shroud.

Winter24.jpg

Step 4

Almost there. Now remove your two AC vent trim pieces. Be careful with this part, as these are the pieces that make your car look pretty. They don’t make Lacewood anymore in my case. Put these somewhere soft where they won’t scratch, like on the carpet. Use a pry tool to pull them away from the dash on the bottom. Make sure you’ve removed the screw holding them into the dash on the top as well (it’s one reason we raised the dash in the last step).

Now you have access to the final two screws.

Winter25.png